My 2 outdoor outlets and 1 in the garage stopped working out of nowhere yesterday. I hit reset on all the GFCI outlets, but we don’t have any tripped breakers. I have noticed that one outdoor outlet is quite loose and it was being used when the 3 outlets stopped working. Any recommendations? Thanks

What kind of wire and breaker and plug do I need?I have the new cord also

I am in the process of trying to switch an outdoor outlet switch combo and not sure how to wire the new one up. The orientation in the box was switch side up. The wires in the box are red, white and ground. The red was connected to the silver terminal, the white to the right side and there is a black jumper wire between the two sides. How do I get it to work with a GFCI?

Hey y’all! I’m wondering if anyone can tell me how best to add something in between this bathroom light fixture and the wall so that I can mount this light about 2 inches further from the wall.

I have an old house (WWII era) and this light fixture also serves as the only outlet in my bathroom. Whenever I plug my hair dryer into this plug it pulls the light off of the wall, hence it being loose and a total eyesore. I’m wondering how to safely build a box underneath it that would distance it from the wall and enable me to use my beauty appliances more easily! In addition to it being the only light source and outlet, I love this light vintage fixture also, so I do not want to change it out.

Appreciate the help in advance!

Why does nobody make an airtight “old work” box that is suitable for vapour and air barrier seal?

I’m moving an outlet on the warm side of on a exterior wall, the old outlet location I’ll foam gasket and blank plate, but my new outlet where I’ll open the vapour barrier and install my new box, what are my options? I can’t get a boot in, unless I somehow manage to tuck the flanges between drywall and vapour barrier, but I can’t tuck tape it anyway without making a giant hole around it- don’t want to do that.

What’s the code compliant way to do this while maintaining my vapour barrier and air sealing?

I am rearranging furniture in my house, and I realize that one of my cable outlets does not work. It is exactly where I wanted to move my desk where the Wi-Fi is set up. Who do I call for this? I’m not sure if it would be an electrician or the cable company?

Hello! I am finishing my garage ceiling with drywall. The wires going into the top of the breaker panel do not have any conduit and go vertically into the rafters where they’ll be hiden by the drywall. As they go up the wall, I am looking to protect them with conduit.
I am thinking about getting 6” PVC and cutting it in half lengthwise to make 2 channels for the vertical cable runs. I cant find actual electrical conduit that is 6” diameter. Any suggestions in how to properly do this without running conduit for each individual wire? Thanks!

I want to upgrade my light switch from white plastic to black metal but struggling to work out the wiring. It’s a single light switch which turns on my main kitchen ceiling light however there are 6 wires.

I’ve just changed all of the upstairs light switches simply however downstairs is proving more difficult.

Can anybody tell me what goes where please? From research, apparently one of the black wires should have red tape on but they both look identical.

House was built in 2000 and the switches haven’t been touched since

I had some recessed lights installed 5-6 years ago. Every once in a while they would all flicker. Recently it had become more constant that the light would flicker from dim to bright constantly. All of the lights are flickering together. Is this a problem with the connection at the switch?

I am trying to run 1 1/2 conduit from my unfinished basement to my attached garage to install an 100 amp sub panel for an EV charger and some additional 20 amp outlets and lights. Ideally I would like to place the sub panel recessed in the wall so it looks nicer. However, I am not sure if that is possible as the only way I can run the 1 1/2 conduit would be to cut a hold on the edge of this horizontal 2x4. The pictures might be confusing because I did attempt to run the conduit horizontally into the garage but I would like to avoid that if possible.

I have always read that you should drill a hole dead center of whatever board you are going through. This would be the opposite of that but I am not sure what the purpose of this horizontal board is. Is ok to compromise it and drill a hole into its edge?

I just updated the overhead fixtures in my basement. Haven’t looked behind any of the outlets (just bought the house in June) until I went to put a dimmer switch on this one. Anybody know what these red wires are, and why the white wires would be capped in the back of the box?

All power has been cut to this outlet!

Both these switches have connected switches on another side of the room. Both lead to separate sets of overhead lights.

Swapped a standard vanity fixture for an LED bar in the guest bath last weekend. Same 15 amp circuit that runs the bathroom fan and two GFCI outlets. The single pole switch now gets warm to the touch after the light has been on for about twenty minutes. Fixture pulls 18 watts total so load should be fine. Wiring looked solid when I pulled the old fixture, 14 gauge with backstabs on the switch and a pigtail to the outlets. No flickering or dimming anywhere else on the circuit. Checked voltage at the switch with the light on and it sits at 119-120. Only thing different is the LED driver versus the old incandescent. Not sure if the backstab is heating or if the switch itself is marginal. Curious if anyone has seen this exact setup cause issues or if I should just replace the switch and pigtail it properly while I'm in there.

About four years ago, I added four LED flush-mount lights to my living room, tapping into the existing ceiling-fan feed. The existing wiring is 12/2, but I used 14/2 for the added lights after being told it would be easier to work with and fine for the small LED load.

I’ve since learned that 14-gauge branch-circuit wiring generally requires a 15-amp breaker, and I confirmed this circuit has a 20-amp breaker. Everything has worked without any noticeable issues, but I want to correct it.

I have attic access and am willing to replace the added runs with 12/2. Is that the best approach, or would changing the breaker to 15 amps be appropriate after verifying everything the circuit supplies?

Appreciate any guidance.

-------------------------------------------------------------------------------------------------

Additionally

Here’s the schematic of my two rooms: https://imgur.com/a/FtERVWq

Living room: The fan and puck lights have separate switches. The 14/2 feeds only the puck lights and ends at the last one.

Garage: I tapped into the original center light and added the puck lights using 14/2.

Shared on Circuits:
Circuit 01: Garage lights, guest bathroom, hallway light
Circuit 02: Living room, hall closet light, living room outlets (TV)

From my understanding, because the LED puck light is the the last in line on that 14/2 wire, and nothing else is passing through it, the only thing providing any load to the 14/2 are those lights. So even if someone plugs in a hair dryer in the guest bathroom, that energy isn't passing through the 14/2. Am I understanding that correctly?

Hi everyone,

I’m from Kerala, India, and I’m facing an electrical problem at home. Please help me understand what could be causing it.

• My house lights sometimes blink when I use my HP gaming laptop charger.
• Some LED tube lights have stopped working.
• Switching appliances like the AC, TV, or fan sometimes stops the flickering.
• The same laptop charger works fine at another house.
• A screwdriver tester glows when touching the socket’s earth pin, and my electrician concluded that current is leaking to earth.
• Even after disconnecting the earth wire at that socket, the lights still flicker.
• Connecting my room’s neutral to a different neutral connection temporarily stopped the problem for two days, but it returned.

The wiring has not been properly diagnosed yet.

Could this be a faulty charger, loose neutral, earthing issue, or incoming power supply problem? What should an electrician check?

can someone pls help me in this problem😭😭

Resident states has random power outages olny in bedrooms on two sides of the apartment both are on 20amp breakers that are not tripping, on two different sides of the panel on separate legsas far as i can tell. Can't find anything shorting out nothing burnt nothing out of the ordinary can't repeat the result. my olny maybe is switch out breakers. Any suggestions is welcomed

Light bulb stopped working so I replaced it with a new one and it still won't turn on, google is telling me to replace the middle part, the ballast

Can anyone help us identify the aircon switch?Mum's aircon is playing up and last time we switched it off and back on after 20 minutes, worked great. That was a while ago and have had electriical work done since... now there is no label on the switch, and whilst I'm handy, I have no idea what you guys know... and don't want to have to run around and reset every single clock and device she uses and needs. Cry for help and thanks in advance if you can help

Help me install these wires?

looking for help before we spend a fortune. A single wall socket stopped working abruptly with no clear cause why. my partner knows some basic things so he took apart the socket. He has a tester to check for current and there is no current coming to that socket. The rest of the sockets connected to the fuse board have current. Any idea how a single one would stop working and if there’s any easy fix to it?

Why does this happen every time I press the power button? Whenever I press it to turn on the AC, the display shows all these details, and I have to keep pressing the button repeatedly until the AC finally turns on.Plz find me solution 🙏

Im building a speaker backpack, and a big problem is my power situation. Im using 2 ryobi 8 ah 18v lithium batteries that go to an Unrulysoul Amazon 60a 24v to 12v step down converter. But its kind of a piece of shit. It cuts out when im pulling maybe 10-15 amps MAYBE. My amp on peak will pull 47 amps as rated in the details but since i have the gains turnt down, i pull maybe 20-30 amps. Im looking for one that can handle at least 60 amps. And thats isn’t a piece of crap. Please help, it sounds good and very loud on 20% volume, imagine 100% volume.

Inherited a parents house and slowly doing it up.
Extractor fan in bathroom doesn’t work. It’s linked to light switch and used to come on when the light was turned on.
The power light on the fan itself comes on but the fan doesn’t. Any ideas?

I switched off the entire fuse box before changing the bathroom lightbulb. As I removed the casing, 2 of the wires touched and sparks fell. I covered the exposed ends of the wires with electrical tape. Is this unsafe now?

Looking to mount a TV opposite a wall with a 200 amp panel that has some heavy loads. I’m wanting to avoid electromagnetic interference. Directly opposite would be ideal for viewing. Otherwise I have 5’ 3” of wall to work with on the right. I could mount it on the next wall over but I would have it pulled out to view so not ideal. Thoughts on how close I can safely be to not hear any hum?